





Home Assistant Connect AUX-2: audio, RS-232 and Bluetooth proxy
59,00 € INCL. VAT
- Connects devices without a network to Home Assistant: hi-fi system, TV or amplifier over RS-232, Bluetooth devices
- 3.5 mm analog or optical output at 24-bit/48 kHz, Sendspin player and Music Assistant
- PoE 802.3af Ethernet or Wi-Fi, USB-C, 2 RS-232 ports, USB-A for a Connect ZWA-2, Grove port
Business, school or public body? business account Education offers

Home Assistant Connect AUX-2: audio, RS-232 and Bluetooth proxy
59,00 € INCL. VAT
- Description
- Additional information
Description
The Home Assistant Connect AUX-2 (ref. NC-AUX-9758) is a small device designed by Nabu Casa to connect devices that have no network connection to Home Assistant. It turns a hi-fi system into a synchronized audio player, controls TVs and amplifiers through an RS-232 serial port, and adds a Bluetooth proxy for your connected devices.
It connects via Ethernet, powered by PoE or USB-C, or via Wi-Fi. Based on an ESP32-S3 running ESPHome, it is open: unlocked bootloader and firmware published as open source by Nabu Casa.
Its USB-A port also accepts a Home Assistant Connect ZWA-2: the Z-Wave antenna can then be placed where reception is best, connected to Home Assistant over the network.
Highlights
- Quality audio: 3.5 mm analog or optical output (mini-TOSLINK S/PDIF) detected automatically, Texas Instruments PCM5122 converter (112 dB signal-to-noise ratio), 24-bit/48 kHz stereo.
- Synchronized playback: native Sendspin player, enabled by default; Music Assistant groups the AUX-2 with other speakers, including AirPlay and some Sonos.
- Two RS-232 ports: on 3.5 mm jacks, with TX/RX swap switches.
- Bluetooth proxy: dedicated antenna, up to 3 active connections.
- Low power: typical consumption under 1 W, PoE 802.3af or USB-C power.
- Expandable: USB-A for a ZWA-2 or an RS-485 adapter, Grove port for sensors.
Use cases
- Connected hi-fi system: play your streaming services and files on an amplifier, a receiver or active speakers.
- Serial control: TVs, AV amplifiers, projectors, UPS units or air conditioning with an RS-232 port and a Home Assistant integration.
- Modbus RS-485: solar inverters, boilers or sensors, with a Waveshare USB TO RS485 (B) adapter on the USB-A port.
- Bluetooth with more range: extend Home Assistant's Bluetooth coverage to a distant room.
- Z-Wave over the network: relocate a Home Assistant Connect ZWA-2 to the best spot in the home.
Technical specifications
| Features | Value |
|---|---|
| Manufacturer reference | NC-AUX-9758 |
| Processor | ESP32-S3R8 (8 MB PSRAM), 8 MB flash |
| Audio output | 1 jack (3.5 mm), analog or optical (mini-TOSLINK S/PDIF), one at a time, automatic detection |
| Audio converter | Texas Instruments PCM5122, 112 dB SNR |
| Audio format | 24-bit/48 kHz stereo; FLAC, MP3, WAV |
| Playback | Native Sendspin player, Music Assistant |
| Serial ports | 2 RS-232 on 3.5 mm TRS jacks (±5 V), TX/RX switches |
| USB-A | 1 Connect ZWA-2, or Waveshare USB TO RS485 (B) adapter; Connect ZBT-2 experimental (ZHA) |
| Extension | Grove port (I2C/GPIO) |
| Network | Ethernet (W5500) with PoE 802.3af or higher; 2.4 GHz Wi-Fi b/g/n |
| Bluetooth | Bluetooth 5 LE, proxy with dedicated antenna, up to 3 active connections (no Bluetooth audio) |
| Power supply | USB-C 5 V 2 A or PoE, one source at a time; typical consumption under 1 W |
| Software | ESPHome, unlocked bootloader, open source firmware |
| Operating conditions | Indoors, 0 to 65 °C, non-condensing |
| Dimensions and weights | 106 x 63 x 25 mm, 104 g |
| With packaging | 110 x 72 x 28 mm, 136 g |
| Compliance | CE, FCC, RCM |
Compatibility and what you need to know
You need Home Assistant 2026.9 or later, with the ESPHome integration. Complete the setup within 15 minutes of powering on, the period during which the device stays in pairing mode.
The AUX-2 only controls serial devices for which Home Assistant has an integration, for example Denon RS-232, LG TV via Serial or Samsung ExLink. It does not amplify sound: passive speakers need an amplifier. It has no audio input, does not do Bluetooth audio and does not support Thread.
Caution: the three 3.5 mm jack sockets look alike but are not interchangeable. Plugging an audio cable into a serial port, or the reverse, can damage the devices. The TX/RX switches are factory-set to X; LG TVs require position II.
On Ethernet without PoE, power the device via USB-C. Wi-Fi turns off when the network cable is plugged in; on USB-C power, the device switches back to Wi-Fi if you unplug the cable. The Connect ZBT-1 is not supported; the ZBT-2 is supported experimentally (ZHA, Home Assistant 2026.11 and firmware 2026.10.4 or later).
Box contents
- 1 Home Assistant Connect AUX-2
- 1 quick start guide
- 1 warranty and safety leaflet
No cable or power supply is included. Plan for an Ethernet cable and a PoE 802.3af or higher switch or injector, such as the Raspberry Pi PoE+ Injector (802.3af and 802.3at, to be completed with its power cable), or a 5 V 2 A USB-C power supply such as the Raspberry Pi USB-C 27 W power supply. Add the audio or serial cables suited to your equipment.
See also the Home Assistant Green, the adapter Home Assistant Connect ZWA-2, the voice assistant Home Assistant Voice Preview Edition, our gateways and home automation modules and the Home Assistant brand.
Frequently asked questions
Does the AUX-2 work without Home Assistant?
No. Nabu Casa designed it as a native Home Assistant device, for local control. You need Home Assistant 2026.9 or later.
Can passive speakers be connected to it?
Not directly: it does not amplify sound. Connect it to a hi-fi system, a receiver or active speakers with an auxiliary or optical input.
Which serial devices can it control?
Those with a Home Assistant integration over RS-232, for example Denon RS-232, LG TV via Serial or Samsung ExLink. Modbus devices on RS-485 go through a Waveshare USB TO RS485 (B) adapter.
Is PoE mandatory?
No. It is powered by PoE 802.3af or higher, or by USB-C 5 V 2 A, and connects via Ethernet or Wi-Fi.
Can a Zigbee stick be connected to it?
The Connect ZBT-2 is supported experimentally, with ZHA. The Connect ZBT-1 is not.
Additional information
| Product type | Audio, serial and Bluetooth connection box for Home Assistant |
|---|---|
| Processor | ESP32-S3 |
| Audio | 3.5 mm analog or optical output, 24-bit/48 kHz |
| Ports | 2 RS-232 (3.5 mm jack), USB-A, Grove, PoE Ethernet, USB-C |
| Home Assistant required | 2026.9 or later |
| Manufacturer reference | NC-AUX-9758 |











